A tap is one of the most essential items in any home, providing a continuous water supply for cooking, cleaning, and personal hygiene. Therefore, faucet installation should be done professionally to ensure faucets function well and life within a household flows smoothly.
However, it’s easy to overlook the importance of proper installation or replacement. A poorly placed faucet can lead to leaks, water damage, and costly repairs. While replacing an old faucet or installing a new one may seem like a simple task, an experienced sanitaryware dealer understands what can go wrong during the process.
If you’re looking for quality faucets and expert installation services, a Premium Sanitaryware Store in Patiala can provide the right products and professional advice to help you avoid common mistakes and enjoy the long-lasting functionality of your faucets.
Common Faucet Installation Problems and How to Fix Them
Some of the common problems you might face through a faucet installation include leaking, low water pressure, and bad fittings. This guide will offer you quite detailed adjusting processes for the problems you are encountering, which in turn will lead to the perfect installation of your faucet, be it in the kitchen or the bathroom.
1. Not Shutting Off The Water Supply
One of the major mistakes that most people make in the installation of sink faucets is forgetting to turn off the water supply. If the water is not turned off, within no time at all, the kitchen or washroom may be flooded, causing high impairment to your home, floors, or cabinets.
How To Avoid
First, locate the shutoff valves for the water supply under the kitchen sink before undertaking the installation process. Usually, those are two small knobs that will control the flow of water to the faucet. You will need to turn them clockwise to shut off the flow of water. If the sink does not have such individual shutoff valves, you need to turn off the main supply to your house. Then, test before you do the installation by turning on the faucet. No water should be flowing.
2. Not Using The Right Tools
This anyway, using the wrong tool or not appropriate for a faucet installation can cause either a befuddled mind or damaged fittings and injuries as well. Using pliers to tighten faucet nuts instead of using the correct wrench may end up with stripped nuts or damage to the faucet itself.
How To Avoid
Before getting down into the installation process, make sure you are appropriately equipped. Tools in front of you would also be necessary for installing a faucet, such as an adjustable wrench, basin wrench, plumbers tape, channel lock pliers, and all type of all other tools required
3. Tightening Connections Too Much
It is worth mentioning that the most common faults in faucet installations are over-tightening nuts that hold the faucet in place or water supply lines. All you need to do is to tighten enough to make sure you do not go overboard as that would result to damage in the faucet, breakage of fittings, stripping of threads and even breaking seals to secure between them, thus posing a risk of water leaking.
How To Avoid
Begin tightening each connection by hand to make it snug but not overly tight. Once that is done, use a wrench to provide slight adjustments by tightening until resistance is felt but avoid using excessive force. It is also vital to follow the manufacturer’s instructions many faucet brands provide specific torque or tightening instructions. These recommendations should also provide the foundation for preventing faucet damage while ensuring connections remain secure.
4. Neglecting The Faucet’s Seal Or Gasket
While installing faucets, a very frequent mistake is either neglecting to position or forgetting to install the gasket or seal that goes between the sink and the faucet. The lack of this seal allows water underneath the faucet base, later leak out and cause water damage and, God knows, some time later, mold growth.
How To Avoid
Be prepared in advance for attaching a faucet, and be ready to place a rubber seal or the gasket between the sink and the faucet in the right position to act as a watertight barrier. Clear off the sink surface and gasket from any dirt to make a better seal. As a last resort, put around the base of the faucet a thin lay of plumber’s putty to make it more secure, or if there is no gasket.
5. Skipping Leak Inspections
After installation of the sink faucet, a few people will not even bother to properly check it for leaks. That being said, water may start leaking from the connections, even if everything looks fine at first sight, and the latencies of the water may cause water damage, mold, or corrosion in time.
How To Avoid
After that, you can reconnect the water and check opening the tap both hot and cold. Immediately inspect the faucet, supply lines, and base for leaks. Furthermore, check under the sink for any leaks at connection points or along the plumbing. If you find any, switch off the water, tighten the connections, and redo the testing.
6. Not Using The Plumber’s Tape
Most frequently, installation errors occur because the plumber is not applying the plumber’s tape (or Teflon tape) at the threaded joints. The plumber’s tape gives a watertight seal and prevents leakage at the points of joinage for pipes or hoses. Even minute gaps between the threads cause continuous dribbling of water.
How To Avoid
When applying the water supply lines, ensure that you cover the male threads of the faucet or supply line fittings with the plumber’s tape. The application should be done using two to three wraps for a good seal but never over-wrapping to prevent difficult fittings. After this installation procedure, turn on the water and check all connections for leaks.
In Conclusion
Installing or changing a faucet is probably one of the easiest jobs ever, but, then again, some extra precautionary steps can save you quite a few bucks. Turn off the water to the faucet; prepare your tools; check for leaks and seal the faucet nicely are some of the things to keep in mind if you want it to last longer and remain leak-free.
This way you avoid the expense of repairs and damage to the water. If you are in Patiala and looking for high-quality faucets & sanitary wares, then Home Design Studio is just one solution for you. It houses vast collections of taps and sanitation in its range, which will be sufficient to furnish your home with fixtures that not only last long but also simultaneously provide attractive utility.
Whether it’s kitchen remodeling or bathroom renovation, help is readily available at Home Design Studio in Patiala anytime with an expert to help find a product that will suffice to meet your needs. Call +918100000697 today to get everything you might need for fast and easy tap installation and any other sanitary needs.
